Rogue Fitness S-4 Squat Stand 2.0 Specs: Height, Footprint and Hole Spacing

The Rogue Fitness S-4 Squat Stand 2.0 is a squat stand in the $400 to $500 price band. It is a pair of independent 72 inch H-base stands rather than one connected frame, which makes it the most spatially flexible squat setup Rogue sells and the least convenient to set up.

What are the Rogue Fitness S-4 Squat Stand 2.0 specifications?

Every figure below is the manufacturer's or retailer's published specification. Where a figure could not be verified against a published source it is omitted from the table rather than estimated, because a guessed dimension is worse than a missing one on a page you are using to decide whether something fits.

What ceiling height does the Rogue Fitness S-4 Squat Stand 2.0 need?

Clear ceiling height is the distance from the finished floor to the lowest obstruction over the rack footprint, which in a basement is a duct run, a beam, a sprinkler head or a light fixture far more often than it is the ceiling itself. The rule is the rack height plus about 2 inches.

For this rack that is 74 inches, derived from the published 72 in height. That figure is our arithmetic on the manufacturer's number, not a manufacturer's number itself.

This is one of the racks that clears a 7 foot basement, which is the single most common constraint people write to us about. Clearing the rack is not the same as clearing a pull-up, though: you need your own standing height plus roughly 14 inches to get your chin over a bar, and in a 7 foot room that arithmetic fails for most adults. Run your own measurement through the ceiling height calculator before ordering, and see the rack height and clearance chart for how the bands compare.

There is a second clearance almost nobody plans for: you have to stand the frame up during assembly. Tilting a 72 inch structure into place in a 74 inch room does not work, and a heavy gauge frame is far harder to raise than a light one. If your headroom is within about 2 inches of the rack height, build it lying down and raise it with a second person.

How much floor space does the Rogue Fitness S-4 Squat Stand 2.0 need?

The barbell sets the floor space, not the rack. A 7 foot Olympic bar is 86.6 inches long, so any barbell lift needs at least 108 inches, which is 9 feet, of clear width no matter how compact the frame is. That is true of every rack on this site and it is the reason a very narrow rack rarely solves a narrow room.

The published footprint here is 22 by 26 inches, about 4 square feet of floor. Add roughly 24 inches of walk-around on the two sides you load plates from and the practical zone is closer to 5.8 by 4.2 feet, which is derived rather than published. The gym space planner will fit it against your actual room dimensions.

What attachments fit the Rogue Fitness S-4 Squat Stand 2.0?

Three numbers decide attachment compatibility: the upright tube size, the hole diameter and the hole spacing. An attachment made for 2 by 3 inch uprights on 5/8 inch hardware will not fit 3 by 3 inch uprights on 1 inch hardware, and spotter arms that almost fit are spotter arms that do not fit.

This rack uses 2 x 3 in 11 ga uprights on 5/8 in hardware, with 2 in with 1 in westside spacing through the bench and clean pull zone hole spacing. The 2 by 3 inch, 5/8 inch Infinity pattern, so it shares accessories with the Rogue R series racks. Compatibility across brands is a convention rather than a guarantee. Manufacturers revise dimensions between production runs without renaming a model, so the only safe check is to measure your own uprights: outside tube dimensions, hole diameter, and hole centre to centre spacing. The hole spacing and gauge chart covers what each measurement means.

At 11 ga the upright wall is about 0.12 inches thick. Gauge is a wall thickness designation rather than a strength rating, and a lower gauge number means thicker steel: 11 gauge is roughly 0.120 in, 12 gauge roughly 0.105 in, and 14 gauge roughly 0.075 in. Thicker wall resists the flex you feel when a heavy bar is racked off centre, which is a different thing from the rack's published capacity.

The one accessory worth buying with any rack used alone is a set of spotter arms , and the compatibility check above is exactly why: confirm the tube size and whether the holes are 5/8 inch or 1 inch before ordering. Where anchoring is called for, half inch wedge anchors are the common slab specification.

What should you know before buying the Rogue Fitness S-4 Squat Stand 2.0?

• Sold as two independent stands, so the published 22 by 26 in H-base footprint is per stand rather than for the pair.
• Capacity is published by Rogue as tested at 1,000 lb.
• At 72 in it clears a 7 ft basement, which combined with the split design makes it one of the few real options for a shared low ceiling room.

How does the Rogue Fitness S-4 Squat Stand 2.0 compare with similar racks?

Compared here against other squat stands in our data, on the four figures that actually decide a purchase: how tall it is, what the uprights are, how the holes are spaced, and what the manufacturer rates it to. A blank cell means we could not verify that figure, not that the rack lacks the feature.

Who is the Rogue Fitness S-4 Squat Stand 2.0 for?

A shared room where the rack has to move out of the way between sessions.

Two separate stands is a genuine trade rather than a downgrade. You can set them to any width, store them against different walls and carry them one at a time, which no cage allows. What you lose is a fixed reference: every session starts by positioning two objects, and a stand that is 2 inches off is a bar you have to muscle back into place. Buy this for flexibility, not for saving money.

Where to go next

• All rack and rig specs, with a master comparison table
• Best power racks, split into beginner, intermediate and expert picks
• How to choose a power rack, the decision in order
• Complete builds by budget, if the rack is one line of a bigger list
• Hole spacing and gauge chart, for attachment compatibility
• Best squat racks for low ceilings