GOIMU WM3-V4 Folding Squat Rack Specs: Height, Footprint and Hole Spacing
The GOIMU WM3-V4 Folding Squat Rack is a folding wall rack. Confirm the current height on the manufacturer spec sheet before ordering. It sits in the $325 to $400 price band.
The GOIMU WM3-V4 Folding Squat Rack is a folding wall rack in the $325 to $400 price band. It is a folding wall rack with dual plate loaded pulleys built into the frame, so one wall covers squats, presses and cable work, and it is also the least documented product on this page.
What are the GOIMU WM3-V4 Folding Squat Rack specifications?
Every figure below is the manufacturer's or retailer's published specification. Where a figure could not be verified against a published source it is omitted from the table rather than estimated, because a guessed dimension is worse than a missing one on a page you are using to decide whether something fits.
| Specification | GOIMU WM3-V4 Folding Squat Rack |
|---|---|
| Type | Folding wall rack |
| Bolt down | Required |
| Price band | $325 to $400 |
Not listed because we could not verify it from a published source: overall height, overall width, overall depth, upright tube size, steel gauge, hardware size, hole spacing, rated capacity. Get those from the current spec sheet, and tell us through the contact page if the manufacturer publishes a figure we have missed.
What ceiling height does the GOIMU WM3-V4 Folding Squat Rack need?
Clear ceiling height is the distance from the finished floor to the lowest obstruction over the rack footprint, which in a basement is a duct run, a beam, a sprinkler head or a light fixture far more often than it is the ceiling itself. The rule is the rack height plus about 2 inches.
We could not verify a published overall height for this model, so we do not print one and we do not derive a ceiling figure from a guess. Take the height from the current spec sheet, add about 2 inches, and compare it against your own measurement to the lowest obstruction using the ceiling height calculator.
How much floor space does the GOIMU WM3-V4 Folding Squat Rack need?
The barbell sets the floor space, not the rack. A 7 foot Olympic bar is 86.6 inches long, so any barbell lift needs at least 108 inches, which is 9 feet, of clear width no matter how compact the frame is. That is true of every rack on this site and it is the reason a very narrow rack rarely solves a narrow room.
We could not verify published width and depth figures for this model, so the footprint row is omitted rather than estimated. The 108 inch clear width requirement still applies, because it comes from the bar rather than the rack. Use the gym space planner once you have the real dimensions from the spec sheet.
What attachments fit the GOIMU WM3-V4 Folding Squat Rack?
Three numbers decide attachment compatibility: the upright tube size, the hole diameter and the hole spacing. An attachment made for 2 by 3 inch uprights on 5/8 inch hardware will not fit 3 by 3 inch uprights on 1 inch hardware, and spotter arms that almost fit are spotter arms that do not fit.
We could not verify the upright dimensions for this model from a published source, so measure your own before buying anything that bolts on. No tube size, hole diameter or hole spacing is published, so no accessory fitment can be stated. Measure the uprights yourself before buying anything that bolts on. Compatibility across brands is a convention rather than a guarantee. Manufacturers revise dimensions between production runs without renaming a model, so the only safe check is to measure your own uprights: outside tube dimensions, hole diameter, and hole centre to centre spacing. The hole spacing and gauge chart covers what each measurement means.
The one accessory worth buying with any rack used alone is a set of spotter arms , and the compatibility check above is exactly why: confirm the tube size and whether the holes are 5/8 inch or 1 inch before ordering. Where anchoring is called for, half inch wedge anchors are the common slab specification.
What should you know before buying the GOIMU WM3-V4 Folding Squat Rack?
- The listing publishes no overall dimensions at all. What it does publish: the rack protrudes 11.9 in from the wall when folded, occupies about 4.3 sq ft folded and 12.3 sq ft deployed, and needs a minimum ceiling height of 88 in.
- Third party specification claims for this model appear to be copied Rogue RML-3W text, so they were discarded rather than repeated here.
- The 88 in minimum ceiling is the one hard figure to plan around, and it rules this out of most basements.
How does the GOIMU WM3-V4 Folding Squat Rack compare with similar racks?
Compared here against other folding wall racks in our data, on the four figures that actually decide a purchase: how tall it is, what the uprights are, how the holes are spaced, and what the manufacturer rates it to. A blank cell means we could not verify that figure, not that the rack lacks the feature.
| Rack | Height | Uprights | Hole spacing | Rated | Price band |
|---|---|---|---|---|---|
| GOIMU WM3-V4 Folding Squat Rack | $325 to $400 | ||||
| Rogue Fitness RML-3W Fold Back Wall Mount Rack | 90.375 in | 3 x 3 in 11 ga | 2 in with 1 in Westside spacing through the bench and pull zone | $600 to $750 | |
| Rogue Fitness R-3W Fold Back Wall Mount Rack | 90.375 in | 2 x 3 in 11 ga | 2 in with 1 in Westside spacing through the bench and pull zone | $500 to $650 | |
| Titan Fitness T-3 Series Folding Power Rack 82 in | 82.375 in | 2 x 3 in 11 ga | Westside spacing through the bench and clean pull zone, 2 in above and below, 6 in side spacing | 1,100 lb | $400 to $600 |
| Titan Fitness X-3 Series Folding Power Rack 80 in | 80.25 in | 3 x 3 in 11 ga | 2 in on centre with Westside spacing on the front of the uprights, 6 in side spacing | 1,100 lb | $420 to $650 |
| PRx Performance Profile PRO Squat Rack with Pull-Up Bar | 89 in | 3 x 3 in 11 ga | 2 in front with 1 in in the bench area, 2 in side | 1,000 lb | $1,000 to $1,100 |
| PRx Performance Profile ONE Squat Rack with Pull-Up Bar | 89 in | 2 x 3 in 11 ga | 2 in front, 2 in side | 1,000 lb | $800 to $900 |
| Mikolo FOLDGYM Folding Wall Mounted Squat Rack (QJ01) | 86.1 in | 2 x 2 in 14 ga | 2 in | $250 to $325 | |
| Mdeam SR-01 Folding Squat Rack | 87 in | 2.36 x 2.36 in | 1,000 lb | $150 to $200 |
Who is the GOIMU WM3-V4 Folding Squat Rack for?
One wall that has to be the entire gym, in a garage or a basement bay.
The built in pulleys are the reason to look at it, because adding cables normally means a second purchase and a second wall. The reason to be careful is documentation: the listing publishes almost no dimensions, and third party specification claims for this model appear to be copied from an unrelated Rogue rack. Everything it can do depends entirely on how well it is anchored, so treat the wall as the real purchase.
Where to go next
- All rack and rig specs, with a master comparison table
- Best power racks, split into beginner, intermediate and expert picks
- How to choose a power rack, the decision in order
- Complete builds by budget, if the rack is one line of a bigger list
- Hole spacing and gauge chart, for attachment compatibility
- Best home gym gear for small spaces
Frequently asked questions
How much ceiling height does the GOIMU WM3-V4 Folding Squat Rack need?
The manufacturer height for this model is not published in a form we could verify, so we do not list one. Get the overall height from the current spec sheet, add about 2 inches of clearance, and measure your own room to the lowest obstruction over the rack footprint rather than to the joists. Our ceiling height calculator will do the arithmetic once you have the figure.
Will the GOIMU WM3-V4 Folding Squat Rack fit in a 7 foot basement?
We do not publish an unverified height for this model, so we cannot answer it precisely. A 7 foot finished ceiling gives 84 inches of clear height, and a rack needs its own height plus about 2 inches. Racks that clear a 7 foot basement are generally in the 70 to 74 inch band. Measure to the lowest obstruction rather than to the joists, because a duct run or a light fixture usually sets the real number.
What hole spacing and hardware does the GOIMU WM3-V4 Folding Squat Rack use?
The hole spacing for this model is not something we could verify from a published source, so we do not list it. Those three numbers together decide which safety bars, spotter arms, J-cups and attachments will physically bolt on. Attachment compatibility is a convention rather than a guarantee, manufacturers change dimensions between production runs, and the only safe check is to measure your own uprights before ordering anything.
What is the GOIMU WM3-V4 Folding Squat Rack rated to hold?
We could not verify a published capacity figure for this model, so we do not list one. Treat any capacity you find on a retailer listing as the manufacturer's stated figure under their own test conditions rather than a safety margin, and remember that the rating assumes correct assembly, a level floor and anchoring where the instructions call for it.
Does the GOIMU WM3-V4 Folding Squat Rack need to be bolted down?
The manufacturer specifies anchoring for this model, so treat it as required rather than optional. Where anchoring is called for, half inch wedge anchors into a slab are the common specification, and embedment depth rather than bolt length carries the load. Verify slab thickness before drilling, since radiant heating tubing and post-tension cables can both be hidden inside a slab. This is researched guidance, not structural engineering advice.
Is the GOIMU WM3-V4 Folding Squat Rack worth it compared with a cheaper rack?
The built in pulleys are the reason to look at it, because adding cables normally means a second purchase and a second wall. The reason to be careful is documentation: the listing publishes almost no dimensions, and third party specification claims for this model appear to be copied from an unrelated Rogue rack. Everything it can do depends entirely on how well it is anchored, so treat the wall as the real purchase.
How we choose: we compare published manufacturer specifications, stated load ratings, and verified owner reviews. We do not test equipment in person. Rack anchoring, floor loading and spotting carry real injury and property risk, so treat everything here as researched guidance rather than coaching or structural engineering advice, follow the manufacturer's rated capacity and installation instructions, and get a licensed professional involved before you drill into concrete or load a floor you are unsure about.